#include "harddrive.h"
#include "apple2.h"
+#include "dis65c02.h"
+#include "fileio.h"
#include "firmware.h"
+#include "log.h"
#include "mmu.h"
+#include "settings.h"
+#include "v65c02.h" // For dumpDis...
+
+
+static uint8_t bank = 0;
+static uint8_t ramBank = 0;
+static uint8_t deviceID = 7;
+static bool dmaSwitch = false;
+static uint8_t staticRAM[0x2000] = { 0 };
+//static char buffer[2048];
+static uint8_t reg[16];
+
+// Stuff that will have to GTFO of here
+static uint8_t * hdData = NULL;//[(0x10000 * 512) + 0x40];
+
+
+/*
+$2 clears bit 1 and puts it back
+$C clears bit 0 & 1 and puts it back
+$F sets bit 7 and puts it back
+reads $4, if 0 or <= 4 after anding with $BE, CLC & RTS
+ else, put $81 into $C88F, else SEC & RTS (obv. failure mode)
+$3 is cleared before going to $CF2F
+ which sets, clears, then sets again bit 7 of $E
+
+$C bits:
+ 0:
+ 1:
+ 2:
+ 3:
+ 4:
+ 5:
+ 6: Physical DMA switch on card
+ 7:
+
+$F bits:
+ 0-2: RAM bank # (?)
+ 3: Enable RAM bank in bits 0-2 (or make writable maybe?)
+ 4-7: ???
+
+Switches on the card:
+#1 sets DMA on/off (switch pos UP = OPEN = off)
+#2-4 sets the computer's SCSI ID number (preset at factor to 7)
+
+Looks like bits 5-7 of register $E is device ID
+
+From Apple II SCSI Card Tech. Ref.:
+
+$0 R Current SCSI data register
+$0 W Output data register
+$1 R/W Initiator command register
+$2 R/W Mode Select register
+$3 R/W Target command register
+$4 R SCSI bus status
+$4 W Select enable register
+$5 R Bus and Status register
+$6 R Input data register
+$7 R Reset parity/interrupts
+
+$8 R/W PDMA/DACK
+$9 R SCSI device ID
+$A W Memory Bank Select register
+$B W Reset 5380 IC
+$D W PDMA mode enable
+$E R Read DRQ status bit through D7 bit
+
+N.B.: The A2 HS SCSI card wires the A0-A2 lines backwards. So it maps like so: (No, it must be a mistake on the schematic as the code doesn't line up with that interpretation)
+
+ZP locations:
+$42 Command number
+$43 Unit number
+$44-45 Buffer pointer
+$46-47 Block number
+
+0123456789ABCDEF
+@ABCDEFGHIJKLMNO
+PQRSTUVWXYZ _
+
+So the path of execution is:
+
+ $CC00 is written to, is that the bank select writable flag (@ reg. $E)?
+ $CD00 hide bank select?
+ $CD01 restore bank select?
+ $C808 gets slot # (+$20)
+ $C809 gets 0
+ - Bank 11:0
+ $C80B gets set with $98 to signal we've been there already
+ $5D gets flags (6 = running on GS, 5 = bit 6 of reg. $C is set)
+ [could it be that bit 6 of $C is physical DMA enable switch?]
+ $5E is the slot # (+$20)
+ $C80C gets the contents of $5D
+ $C893 gets set with $80 (signal we're in I set mode)
+ $C896 is set with GS Speed Register (0 on non-GS models)
+ $C807 gets set with the SP
+ execution then jumps to...
+ - Bank 15:0
+ $C809 gets $40 (& $BF32 as well!)
+ $C80A gets 0
+ Calls bank 3:0
+ - Bank 3:0 (Look for bootable drive)
+ $C883 gets 0
+ $C815 gets 0
+ $C80D gets 0 (# of drives found?)
+ $C80F gets 0
+ $C8DA gets: Device ID from $E is massaged and changed into a single bit
+ Calls bank 21:3
+ - Bank 21:3
+ Stores $80 (RST) in reg. $1, burns some cycles, stores 0 in reg. $1
+ [Looks like ASSERT /RST]
+ burn cycles, but burn most if $C8DA == 4
+ Clears 32 bytes @ $C92F
+ $C817 gets $40 |_________________
+ $C818 gets 0 | Failure countdown
+ $C8DB gets SCSI ID # from loop (bit field)
+ $4F gets cleared (error flag)
+ Calls $CF5F (send command to device?)
+ So the buffer (@ $C923) looks like so before the call:
+* 00 00 00 00 00 00 .. .. .. .. .. .. C3 C9 00
+ ^$60/1 points here ^$56/7 points here ($62 = $58 = 0)
+* Puts $C9C3 into $C92F/30, zeroes $C931
+ Then calls bank 16:0
+ - Bank 16:0
+ Stores to $CD00
+ Calls $CDD0
+ Clears bit 1 from reg. $2, bits 0 & 1 from $C
+ [Looks like it clears the DMA MODE bit]
+* Clears $4F, $C806, $C88F, $C890, $C8EE-F0
+ Sets bit 7 of reg. $F
+ Calls $CECE
+ Gets reg. $4, checks for 0, returns success if so
+ [R is SCSI Bus Status]
+ Masks bits 1-5 & 7, checks for 2 or 4, returns success if so
+ [bit 2 = /I/O, bit 1 = /SEL]
+ Else, $81 -> $C88F, returns failure (set bit 7 of $C806, sets C)
+ Calls $CF42
+ Returns since $C893 has $80 in it
+ Calls $CC24 (Arbitrate phase)
+ Zeroes reg. $3
+ [Target Command, set Data Out]
+ Toggles bit 7 of reg. $E (ON-off-ON)
+ Puts host ID(?) in reg. $0
+ [W: Output Data - sends data on SCSI bus]
+ Loop:
+ Puts 0 in reg. $2, then sets bit 0 of reg. $2
+ [bit 0 is ARBITRATE, requires SCSI device ID in $0]
+ Gets reg. $C, checks bit 4
+ If clear, then toggle reg. $E (ON-off-ON) & count down to failure
+ Check bit 6 of reg. $1, loop back if not set
+ [Initiator Command. bit 6 AIP, if set bus free detected]
+ Check bit 5 of reg. $1, loop back if not clear
+ [Initiator Command, bit 5 LA, if set, bus was lost]
+ Check reg. $0 to see if it's same as what's in $C8DA
+ [R: Current SCSI Data]
+ If not, see if it's >= to EORed value & loop back if it is
+ Checks bit 5 of reg. $1, loop back if not clear
+ [Initiator Command, bit 5 LA, if set, bus was lost]
+ Sets bits 1 & 2 of reg. $1, clear bits 5 & 6 of same
+ [Initiator Command: 1 = ASSERT /ATN, 2 = ASSERT /SEL, clear AIP, LA]
+ Clear C and return if success, set $C88F to $80 & set C if failure
+ Calls $CC7A if succesful:
+ Zeroes out reg. $4
+ [Select Enable: disable interrupts]
+ Stores $C8DA ORed with $C8DB into reg. $0
+ [W: Output Data - writing ?]
+ Set bits 0 & 6 in reg. $1, clear 5 & 6 in reg. $1
+ [W: 0- ASSERT DATA BUS, 6- TEST MODE; 5- unused(?), 6- TEST MODE off]
+ Clear bit 0 in reg. $2
+ [W: Clear ARBITRATE]
+ Puts contents of $C8DC +set bit 7 into $C821
+ Clears bit 3 in reg. $1
+ [W: 3- ASSERT /BSY (0 disconnects from bus)]
+ Calls $CD51
+ Toggle bit 7 of reg. $E (ON-off-ON)
+ Wait for bit 6 of reg. $4 to come on, if not, set C (signal failure)
+ [R: bit 6- /BSY]
+ Clears bit 2 in reg. $1
+ [W: ASSERT /SEL (0 de-asserts)]
+ Clears bits 1, 5, 6 in reg. $1
+ [W: 1- /ATN, 5- unused(?), 6- TEST MODE]
+ Clears bit 0 in reg. $1
+ [W: ASSERT DATA BUS (0 de-asserts)]
+ Signals success (C = 0) or failure (C = 1, $C88F = $81)
+ Calls $CF58
+ Returns since $C893 has $80 in it still
+ Calls $CCE4
+ Checks if bit 4 of reg. $C is set, if not, toggle bit 7 of reg. $E
+ Checks $4, if either of bits 1 & 6 are set, if not, signal failure
+ If only bit 2 or 2 & 6 is set, loop back to beginning of call
+ Clears bit 1 of reg. $2, then restores it to what it was
+ [W: 1- DMA MODE]
+ Checks for bit 5 of reg. $4, if not set, loop back to begin
+ [R: 5- /REQ]
+ Moves $C81F into $C820
+ Restores reg. $4 from Y, masks off bits 2-4 and puts it in $C81F
+ [R: 4- /MSG, 3- /C/D, 2- /I/O]
+ Puts prev. value r. shifted 1 into $C82B
+ Uses that as index into jump table
+ R. shifts again by 1 and stuffs into reg. $3
+ [W: Target Command- writes /MSG, /C/D, /I/O]
+ Calls $CD48
+ Using Y as index, push value pair @ $CFB4 onto stack & return to call
+ Calls a routine from 0-7...
+ 0-1 goes to $6E6C or copies $56-8 into $C81C-E, calls bank 18:0
+ - Bank 18:0
+ ...
+ Calls bank 20:0 or 1 (0 for read, 1 for write--PIO mode)
+ 2 calls bank 17:0 (/C/D)
+ 3 calls bank 17:3 (/C/D + /I/O)
+ 4-5 signals failure & returns (bit 4: /MSG, no /C/D = failure)
+ 6 calls bank 17:2 (/MSG + /C/D)
+ [During init, it comes here...]
+ Gets $C821, compares it to 1, if so, signal failure & return
+ Calls $CE79
+ a
+ 7 calls bank 17:1 (/MSG + /C/D + /I/O)
+ If bit 7 of $C806 is clear, loop back to begin
+ Calls $CDA0
+ Does some error checking on $C88F and $C8EC
+ Jumps to $CE18
+ Clears bit 1 from reg. $2, bits 0-1 from reg. $C
+ Moves $C88F into $4F
+ If it's 0 or $8E, or reg. $4 is 0, skip over next
+ Calls $CE6C
+ Moves $C88F into $4F
+ Zeroes out regs. $1, $2, $3, $C
+ Stores to $CD01
+ [Returns to $CC6D in bank 3:0]
+ Calls $CC9F (Function 1 - INQUIRY + more
+ Zeroes $C8CF, $C892
+ Calls $CD0E
+ [12 00 00 00 1E 00 .. .. .. .. .. .. C3 C9 00 .. 1E]
+ Calls bank 16:0 (Do INQUIRY)
+ if $C9C3 (1st byte of INQUIRY data) == $10
+ $C892 <- $80
+ $C8CB <- $06
+ $C8B9 <- $F8
+ $C8CC <- $C0
+ else if == 2 or 6,
+ $C892 <- $40
+ $C8CF |= $0C
+ else (depending on 1st byte),
+ (5=CDROM, 6=DA Tape drive, 7=HD, 8=Scanner, 9=Printer, 3=nonspecific)
+ $C8CB <- 07 06 09 FF FF 05 08
+ $C8B9 <- C0 C0 A0 00 00 C0 A0
+ $C8CC <- F8 F8 78 FF FF B4 70
+ Sets bit 5, clears bit 6 in $C8CC
+ if bits 4-5, 7 are set, set bit 0 of $C8CF
+ Copies 16 bytes of returned data from $C9C3 + $17 to $C8BB
+ $C8CE <- $30
+ $C8CD <- $00
+ Calls bank 21:1 (lock CD-ROM?)
+ Does PREVENT ALLOW MEDIUM REMOVAL if $C8CB == 5
+ $C927 <- $01
+ Calls $CDDD (MODE SENSE/MODE SELECT)
+ Calls $CEA8 (READ CAPACITY)
+ Calls 16:0 with command READ CAPACITY, data returned @ $C9C3 (8 bytes)
+ $C8AB <- $C9C6
+ $C8AA <- $C9C5
+ $C8A9 <- $C9C4
+ if $C8A9 =! 0, set bit 0 of $C8CF
+ $C8A8 <- $C9C3
+ if $C8A8 != 0, set bit 0 of $C8CF
+ $C8AF <- $C9C7, save flags
+ $C8AE <- $C9C8, save flags
+ $C8AD <- $C9C9, save in Y
+ $C8AC <- $C9CA
+ Zeroes error flag ($4F)
+ $C8CF |= 0x0C
+ Calls $CFC7 (bank 4:0 direct)
+ - Bank 4:0
+ Calls $CD65 (READ--reads 512 bytes from LBA set from $C8D2 + 1)
+ Calls $CDDA, sets carry if 1st two bytes are not 'PM'
+ Calls $CD39
+ Calls $CD1A
+ $C8D0 <- $C80F
+ Calls $CDF1
+ [Returns to $CCDB in bank 3:0]
+ Loops back if bit 7 of $C892 is clear
+ Calls $CD05 (bank 21:2 direct--unlock CD-ROM?)
+ Adds 1 to $C8DC
+ Loops back if $C8DC != 8
+ ...
+ [Returns to $CC10 in bank 15:0]
+ Checks if call was successful (if not jumps to bank 11:1)
+ execution jumps to...
+ - Bank 11:2 ($CD9A)
+ Puts 1 in $43 (unit #), $44
+ Zeroes out $46-49 (block # [2], ??? [2])
+ Puts $08 in $41, zeroes out $40, $42 (command)
+ Calls bank 9:0
+ - Bank 9:0
+ ...
+ Calls bank 16:0
+
+SCSI Phases
+-----------
+
+Selection: In this state, the initiator selects a target unit and get the target to carry out a given function, such as reading or writing data. The initiator outpus the OR value of its SCSI-ID and the SCSI-ID of the target onto the data bus (for example, if the initiator is 2 and the target is 5 then the OR-ed ID on the bus will be 00100100). The target then determines that its ID is on the data bus and sets the /BSY line active. If this does not happen within a given time, then the initiator deactivates the /SEL signal, and the bus will be free. The target determines that it is selected when the /SEL signal and its SCSI ID bit are active and the /BSY and /I/O signals are false. It then asserts the signal within a selection abort time (200µs).
+*/
+static bool DATA_BUS = false;
+static bool DMA_MODE = false;
+static bool BSY = false;
+static bool ATN = false;
+static bool SEL = false;
+static bool ACK = false;
+static bool RST = false;
+static bool MSG = false;
+static bool C_D = false;
+static bool I_O = false;
+static bool REQ = false;
+static bool DEV_BSY = false;
+static bool DRQ = false;
+static bool DACK = false;
+static uint8_t devMode = 8;
+static uint8_t cmdLength;
+static uint8_t cmd[256];
+static uint32_t bytesToSend;
+static uint8_t * buf;
+static uint32_t bufPtr;
+
+
+static void RunDevice(void)
+{
+//WriteLog(" >>> RUNNING HD...\n");
+ // Let's see where it's really going...
+/* if (mainCPU.pc == 0xCE7E)
+ dumpDis = true;//*/
+
+ static uint8_t readCapacity[8] = { 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x02, 0x00 };
+ static uint8_t inquireData[30] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 'S', 'E', 'A', 'G', 'A', 'T', 'E', ' ', 'P', 'h', 'o', 'n', 'y', '1' };
+
+ enum {
+ DVM_DATA_OUT = 0, DVM_DATA_IN = 1, DVM_COMMAND = 2, DVM_STATUS = 3,
+ DVM_MESSAGE_OUT = 6, DVM_MESSAGE_IN = 7, DVM_BUS_FREE, DVM_ARBITRATE,
+ DVM_SELECT
+ };
+
+ if (RST)
+ {
+WriteLog(" >>> DEVICE RESET...\n");
+ devMode = DVM_BUS_FREE;
+ DEV_BSY = false;
+ return;
+ }
+
+ switch (devMode)
+ {
+ case DVM_BUS_FREE:
+ if (SEL)//(BSY && SEL)
+ devMode = DVM_ARBITRATE;
+
+ break;
+ case DVM_ARBITRATE:
+//WriteLog(" >>> ARBITRATE PHASE (BSY=%i SEL=%i DATA_BUS=%i [%02X])\n", BSY, SEL, DATA_BUS, reg[0]);
+ if (!BSY && SEL && DATA_BUS && (reg[0] & 0x40))
+ devMode = DVM_SELECT, DEV_BSY = true;
+ else if (!BSY && !SEL)
+ devMode = DVM_BUS_FREE;
+
+ break;
+ case DVM_SELECT:
+WriteLog(" >>> SELECT PHASE\n");
+ if (ATN)
+ {
+ MSG = true, C_D = true, I_O = false;
+ devMode = DVM_MESSAGE_OUT;
+ REQ = true;
+ }
+ else
+ {
+ // If no ATN is asserted, go to COMMAND I guess?
+ // Let's try it
+// errrr, no. this does not work. Or does it???
+ MSG = false, C_D = true, I_O = false;
+ devMode = DVM_COMMAND;
+ cmdLength = 0;
+ }
+
+ break;
+ case DVM_DATA_OUT:
+WriteLog(" >>> DATA OUT PHASE\n");
+ if (!ACK)
+ REQ = true;
+
+ if (DMA_MODE)
+ {
+ if (!DACK)
+ {
+ // We just send zeroes for now...
+ reg[6] = 0;
+ DRQ = true;
+ }
+ else if (DRQ && DACK)
+ {
+ DRQ = false;
+ DACK = false;
+ bytesToSend--;
+
+ if (bytesToSend == 0)
+ {
+ REQ = false;
+ MSG = false, C_D = true, I_O = true;
+ devMode = DVM_STATUS;
+ }
+ }
+ }
+
+ break;
+ case DVM_DATA_IN:
+WriteLog(" >>> DATA IN PHASE (bts=%u)\n", bytesToSend);
+ if (!ACK)
+ REQ = true;
+
+ if (DMA_MODE)
+ {
+ if (!DACK)
+ {
+ // We just send zeroes for now...
+ if (buf == NULL)
+ reg[6] = 0;
+ else
+ reg[6] = buf[bufPtr];
+
+ DRQ = true;
+ }
+ else if (DRQ && DACK)
+ {
+ DRQ = false;
+ DACK = false;
+ bytesToSend--;
+ bufPtr++;
+
+ if (bytesToSend == 0)
+ {
+ REQ = false;
+ MSG = false, C_D = true, I_O = true;
+ devMode = DVM_STATUS;
+ buf = NULL;
+ }
+ }
+ }
+
+ break;
+ case DVM_COMMAND:
+WriteLog(" >>> COMMAND PHASE\n");
+ if (!ACK)
+ REQ = true;
+ else if (REQ && ACK)
+ {
+ cmd[cmdLength++] = reg[0];
+ WriteLog("HD: Write to target value $%02X\n", reg[0]);
+ REQ = false;
+ }
+
+ // Handle "Test Unit Ready" command
+ if ((cmd[0] == 0) && (cmdLength == 6))
+ {
+ WriteLog("HD: Received command TEST UNIT READY\n");
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = true, I_O = true;
+ devMode = DVM_STATUS;
+ }
+ // Handle "Request Sense" command
+ else if ((cmd[0] == 0x03) && (cmdLength == 6))
+ {
+ WriteLog("HD: Received command REQUEST SENSE [%02X %02X %02X %02X %02X %02X]\n", cmd[0], cmd[1], cmd[2], cmd[3], cmd[4], cmd[5]);
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = false, I_O = true;
+ devMode = DVM_DATA_IN;
+ bytesToSend = cmd[4];
+ }
+ // Handle "Read" (6) command
+ else if ((cmd[0] == 0x08) && (cmdLength == 6))
+ {
+ WriteLog("HD: Received command READ(6) [%02X %02X %02X %02X %02X %02X]\n", cmd[0], cmd[1], cmd[2], cmd[3], cmd[4], cmd[5]);
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = false, I_O = true;
+ devMode = DVM_DATA_IN;
+ bytesToSend = cmd[4] * 512; // amount is set in blocks
+ }
+ // Handle "Inquire" command
+ else if ((cmd[0] == 0x12) && (cmdLength == 6))
+ {
+ WriteLog("HD: Received command INQUIRE [%02X %02X %02X %02X %02X %02X]\n", cmd[0], cmd[1], cmd[2], cmd[3], cmd[4], cmd[5]);
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = false, I_O = true;
+ devMode = DVM_DATA_IN;
+ bytesToSend = cmd[4];
+ buf = inquireData;
+ bufPtr = 0;
+ }
+ // Handle "Mode Select" command
+ else if ((cmd[0] == 0x15) && (cmdLength == 6))
+ {
+ WriteLog("HD: Received command MODE SELECT [%02X %02X %02X %02X %02X %02X]\n", cmd[0], cmd[1], cmd[2], cmd[3], cmd[4], cmd[5]);
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = false, I_O = false;
+ devMode = DVM_DATA_OUT;
+ bytesToSend = cmd[4];
+ }
+ // Handle "Mode Sense" command
+ else if ((cmd[0] == 0x1A) && (cmdLength == 6))
+ {
+ WriteLog("HD: Received command MODE SENSE [%02X %02X %02X %02X %02X %02X]\n", cmd[0], cmd[1], cmd[2], cmd[3], cmd[4], cmd[5]);
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = false, I_O = true;
+ devMode = DVM_DATA_IN;
+ bytesToSend = cmd[4];
+ }
+ // Handle "Read Capacity" command
+ else if ((cmd[0] == 0x25) && (cmdLength == 10))
+ {
+ WriteLog("HD: Received command READ CAPACITY [%02X %02X %02X %02X %02X %02X %02X %02X %02X %02X]\n", cmd[0], cmd[1], cmd[2], cmd[3], cmd[4], cmd[5], cmd[6], cmd[7], cmd[8], cmd[9]);
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = false, I_O = true;
+ devMode = DVM_DATA_IN;
+ bytesToSend = 8;//cmd[4];
+ buf = readCapacity;
+ bufPtr = 0;
+ }
+ // Handle "Read" (10) command
+ else if ((cmd[0] == 0x28) && (cmdLength == 10))
+ {
+ WriteLog("HD: Received command READ(10) [%02X %02X %02X %02X %02X %02X %02X %02X %02X %02X]\n", cmd[0], cmd[1], cmd[2], cmd[3], cmd[4], cmd[5], cmd[6], cmd[7], cmd[8], cmd[9]);
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = false, I_O = true;
+ devMode = DVM_DATA_IN;
+ bytesToSend = ((cmd[7] << 8) | cmd[8]) * 512; // amount is set in blocks
+ uint32_t lba = (cmd[2] << 24) | (cmd[3] << 16) | (cmd[4] << 8) | cmd[5];
+ buf = &hdData[(lba * 512) + 0x40];
+ bufPtr = 0;
+ }
+ else if ((cmdLength == 6) && ((cmd[0] & 0xE0) == 0))
+ {
+ WriteLog("HD: Received unhandled 6 command [%02X %02X %02X %02X %02X %02X]\n", cmd[0], cmd[1], cmd[2], cmd[3], cmd[4], cmd[5]);
+ }
+ else if ((cmdLength == 10) && (((cmd[0] & 0xE0) == 0x20) || ((cmd[0] & 0xE0) == 0x40)))
+ {
+ WriteLog("HD: Received unhandled 10 command [%02X %02X %02X %02X %02X %02X %02X %02X %02X %02X]\n", cmd[0], cmd[1], cmd[2], cmd[3], cmd[4], cmd[5], cmd[6], cmd[7], cmd[8], cmd[9]);
+ }
+
+ break;
+ case DVM_STATUS:
+WriteLog(" >>> STATUS PHASE\n");
+ if (!ACK)
+ {
+ // Return A-OK for everything for now...
+ reg[0] = 0;
+ REQ = true;
+ }
+ else if (REQ && ACK)
+ {
+ REQ = false;
+ // Drive next phase
+ MSG = true, C_D = true, I_O = true;
+ devMode = DVM_MESSAGE_IN;
+ }
+
+ break;
+ case DVM_MESSAGE_OUT:
+WriteLog(" >>> MESSAGE OUT PHASE\n");
+ if (REQ && ACK)
+ {
+ uint8_t msg = reg[0];
+ WriteLog("HD: Write to target value $%02X\n", msg);
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = true, I_O = false;
+ devMode = DVM_COMMAND;
+ cmdLength = 0;
+ }
+
+ break;
+ case DVM_MESSAGE_IN:
+WriteLog(" >>> MESSAGE IN PHASE\n");
+ if (!ACK)
+ {
+ // Return A-OK for everything for now...
+ reg[0] = 0;
+ REQ = true;
+ }
+ else if (REQ && ACK)
+ {
+ REQ = false;
+ // Drive next phase
+ MSG = false, C_D = false, I_O = false;
+ DEV_BSY = false;
+ devMode = DVM_BUS_FREE;
+ }
+
+ break;
+ }
+}
+
+
+static uint8_t SlotIOR(uint16_t address)
+{
+ // This should prolly go somewhere else...
+ RunDevice();
+
+ char SCSIName[16][256] = {
+ "(RO) Current SCSI Data",
+ "Initiator Command",
+ "Mode",
+ "Target Command",
+ "(RO) Current SCSI Bus Status",
+ "(RO) Bus and Status",
+ "(RO) Input Data",
+ "(RO) Reset Parity/Interrupt",
+ "DMA Address LO",
+ "DMA Address HI",
+ "DMA Count LO",
+ "DMA Count HI",
+ "$C",
+ "$D",
+ "Bank/SCSI ID",
+ "$F"
+ };
+
+ uint8_t response = reg[address & 0x0F];
+
+ switch (address & 0x0F)
+ {
+ case 0x00:
+ // (RO) Current SCSI Data register
+ break;
+ case 0x01:
+ // Initiator Command register. Bits, from hi to lo:
+ // ASS. /RST, AIP, LA, ASS. /ACK, A./BSY, A./SEL, A./ATN, DATA BUS
+
+ // Simulate ARBITRATE signal
+ if (reg[2] & 0x01)
+ response |= 0x40;
+
+ break;
+ case 0x02:
+ // Mode register (chip control)
+ break;
+ case 0x03:
+ // Target Command register (SCSI bus info xfer phase)
+ break;
+ case 0x04:
+ // (RO) Current SCSI Bus Status register: Bits from hi to lo:
+ // /RST, /BSY, /REQ, /MSG, /C/D, /I/O, /SEL, /DBP
+if (((mainCPU.pc != 0xCD7C) && (mainCPU.pc != 0xCD5F)) || (bank != 16))
+ WriteLog(" [%02X %02X %02X %02X %02X %02X %02X %02X] [$C81F=$%02X $C80D=$%02X $C80A=$%02X $C887=$%02X $C806=$%02X $C88F=$%02X $C8EC=$%02X $4F=$%02X]\n", reg[0], reg[1], reg[2], reg[3], reg[4], reg[5], reg[6], reg[7], staticRAM[0x1F], staticRAM[0x0D], staticRAM[0x0A], staticRAM[0x87], staticRAM[0x06], staticRAM[0x8F], staticRAM[0xEC], ram[0x4F]);
+
+ response = (RST ? 0x80 : 0) | (BSY | DEV_BSY ? 0x40 : 0) | (REQ ? 0x20 : 0) | (MSG ? 0x10 : 0) | (C_D ? 0x08 : 0) | (I_O ? 0x04 : 0) | (SEL ? 0x02 : 0);
+ break;
+ case 0x05:
+ {
+ // (RO) Bus and Status register
+ response = (ACK ? 0x01 : 0) | (ATN ? 0x02 : 0) | (DRQ ? 0x40 : 0);
+ uint8_t tgtMode = (MSG ? 0x04 : 0) | (C_D ? 0x02 : 0) | (I_O ? 0x01 : 0);
+
+ if ((reg[3] & 0x07) == tgtMode)
+ response |= 0x08;
+
+ break;
+ }
+ case 0x06:
+ // (RO) Input Data register (read from from SCSI bus)
+ if (DRQ)
+ DACK = true;
+
+ break;
+ case 0x07:
+ // (RO) Reset Parity/Interrupt
+ // Resets PARITY ERR (bit 6), IRQ (bit 5), BUSY ERROR (bit 3) in
+ // register 5 (Bus & Status)
+ break;
+ case 0x0C:
+ response = 0x10 | (dmaSwitch ? 0x40 : 0);
+ break;
+ case 0x0E:
+ response = bank | (deviceID << 5);
+ break;
+ }
+
+ if (((mainCPU.pc != 0xCD7C) && (mainCPU.pc != 0xCD5F)) || (bank != 16))
+ WriteLog("HD Slot I/O read %s ($%02X <- $%X, PC=%04X:%u)\n", SCSIName[address & 0x0F], response, address & 0x0F, mainCPU.pc, bank);
+
+ return response;
+}
+
+
+static void SlotIOW(uint16_t address, uint8_t byte)
+{
+ char SCSIName[16][256] = {
+ "(WO) Output Data",
+ "Initiator Command",
+ "Mode",
+ "Target Command",
+ "(WO) Select Enable",
+ "(WO) Start DMA Send",
+ "(WO) Start DMA Target Receive",
+ "(WO) Start DMA Initiator Receive",
+ "DMA Address LO",
+ "DMA Address HI",
+ "DMA Count LO",
+ "DMA Count HI",
+ "$C",
+ "$D",
+ "Bank/SCSI ID",
+ "$F"
+ };
+
+ switch (address & 0x0F)
+ {
+ case 0x00:
+ // (WO) Output Data register (data sent over SCSI bus)
+ if (DRQ)
+ DACK = true;
+
+ break;
+ case 0x01:
+ // Initiator Command register. Bits, from hi to lo:
+ // ASS. /RST, AIP, LA, ASS. /ACK, A./BSY, A./SEL, A./ATN, DATA BUS
+ DATA_BUS = (byte & 0x01 ? true : false);
+ ATN = (byte & 0x02 ? true : false);
+ SEL = (byte & 0x04 ? true : false);
+ BSY = (byte & 0x08 ? true : false);
+ ACK = (byte & 0x10 ? true : false);
+ RST = (byte & 0x80 ? true : false);
+ break;
+ case 0x02:
+ // Mode register (chip control)
+
+ // Dma ReQuest is reset here (as well as by hitting a pin)
+// if ((byte & 0x02) == 0)
+// DRQ = false;
+ DMA_MODE = (byte & 0x02 ? true : false);
+
+ if (!DMA_MODE)
+ DRQ = DACK = false;
+
+ break;
+ case 0x03:
+ // Target Command register (SCSI bus info xfer phase)
+ break;
+ case 0x04:
+ // (WO) Select Enable register
+ break;
+ case 0x05:
+ // (WO) Start DMA Send (initiates DMA send)
+ DRQ = true;
+ break;
+ case 0x06:
+ // (WO) Start DMA Target Receive (initiate DMA receive--tgt mode)
+ DRQ = true;
+ break;
+ case 0x07:
+ // (WO) Start DMA Initiator Receive (initiate DMA receive--ini mode)
+ DRQ = true;
+ break;
+ case 0x08:
+ // Lo byte of DMA address?
+ break;
+ case 0x09:
+ // Hi byte of DMA address?
+ break;
+ case 0x0A:
+ // 2's complement of lo byte of transfer amount?
+ break;
+ case 0x0B:
+ // 2's complement of hi byte of transfer amount?
+ break;
+ case 0x0C:
+ // Control/status register?
+ break;
+ case 0x0D:
+ // ???
+ break;
+ case 0x0E:
+ // Bottom 5 bits of $E set the ROM bank...
+ bank = byte & 0x1F;
+// WriteLog("HD: Setting bank %u\n", bank);
+ break;
+ case 0x0F:
+ // ??? RAM bank? Seems to be
+ ramBank = byte & 0x07;
+ break;
+ }
+
+ WriteLog("HD Slot I/O write %s ($%02X -> $%X, PC=%04X:%u)\n", SCSIName[address & 0x0F], byte, address & 0x0F, mainCPU.pc, bank);
+ reg[address & 0x0F] = byte;
+
+ if ((address & 0x0F) == 0x0E)
+ {
+ if (mainCPU.pc == 0xC78B)
+ {
+ uint16_t sp = mainCPU.sp;
+ uint16_t pc = ram[0x100 + sp + 1] | (ram[0x100 + sp + 2] << 8);
+ WriteLog(" *** Returning to bank %u, $%04X\n", bank, pc + 1);
+ }
+ else if (mainCPU.pc == 0xC768)
+ {
+ WriteLog(" *** Calling to bank %u:%u\n", mainCPU.a, (mainCPU.y & 0xE0) >> 5);
+ }
+
+ WriteLog(" [%02X %02X %02X %02X %02X %02X %02X %02X] [$C81F=$%02X $C80D=$%02X $C80A=$%02X $C887=$%02X $C806=$%02X $C88F=$%02X $C8EC=$%02X $4F=$%02X]\n", reg[0], reg[1], reg[2], reg[3], reg[4], reg[5], reg[6], reg[7], staticRAM[0x1F], staticRAM[0x0D], staticRAM[0x0A], staticRAM[0x87], staticRAM[0x06], staticRAM[0x8F], staticRAM[0xEC], ram[0x4F]);
+ }
+
+ // This should prolly go somewhere else...
+ RunDevice();
+}
+
+
+static uint8_t SlotROM(uint16_t address)
+{
+ return hd2ROM[address];
+}
+
+
+static uint8_t SlotIOExtraR(uint16_t address)
+{
+ if (address < 0x400)
+ return staticRAM[(ramBank * 0x400) + address];
+ else
+ return hd2ROM[(bank * 0x400) + address - 0x400];
+}
+
+
+static void SlotIOExtraW(uint16_t address, uint8_t byte)
+{
+ if (address < 0x400)
+ staticRAM[(ramBank * 0x400) + address] = byte;
+ else
+ {
+ WriteLog("Unhandled HD 1K ROM write ($%02X) @ $C%03X...\n", byte, address + 0x800);
+
+ if ((mainCPU.pc == 0xCDDD) && (bank == 11))
+ dumpDis = true;
+ }
+}
void InstallHardDrive(uint8_t slot)
{
+ SlotData hd = { SlotIOR, SlotIOW, SlotROM, 0, SlotIOExtraR, SlotIOExtraW };
+ InstallSlotHandler(slot, &hd);
+
+ uint32_t size = 0;
+ hdData = ReadFile(settings.hdPath, &size);
+
+ WriteLog("Read Hard Drive image file, %u bytes ($%X)\n", size, size);
}
projects / apple2 / blobdiff