X-Git-Url: http://shamusworld.gotdns.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=include%2Ftransport-bar.html;h=c3bb71bef1dcd1d1d9b949183f9a946cf452c1b3;hb=65c85fa9b607c8c0e852d77c8117e3125181e69c;hp=fa06c4111850a0c00c015e7f664c399f7853e6ee;hpb=b5d2dccf364816fcbc00d4e1abf44f7276533122;p=ardour-manual diff --git a/include/transport-bar.html b/include/transport-bar.html index fa06c41..c3bb71b 100644 --- a/include/transport-bar.html +++ b/include/transport-bar.html @@ -5,70 +5,81 @@ playback and recording.
- + +- This bar is made of (from left to right): + The upper row contains transport actions, that are all bound to keyboard + shortcuts, which allows for speedier use and more focused work:
-Midi Panic | Immediately stops all midi output. |
---|---|
Enable/disable Audio Click | Toggles (on/off) a click track (metronome)
along the tempo. Right clicking brings up the
Click submenu from the Preferences. Scrolling with
- the mouse wheel adjusts the gain of the click.
- |
Go to Start of the Session | Jumps back at the beginning of the session, + as defined by the start marker. |
Go to End of the Session | Jumps forward to the end of the session, + as defined by the end marker. |
Play Loop Range | Repeats the defined loop
as defined by the Loop range, until the "Stop
playback" button is pressed. Clicking the "Play loop Range" button while
already active switches to normal Play mode, which exits the loop without
- stopping and restarting playback.
- |
Play Range/Selection | If a range has been defined using the Range
Mode button, plays the range, of if an audio or MIDI region is selected,
plays this region. In both cases, the playback stops at the end of the range
- or selected region.
- |
Play from playhead | Starts the playback and optionally record (more + below). |
Stop | Whatever the playing mode (loop, range, …) stops all
playback. Depending on other settings, some effects (like chorus or reverb)
- might still be audible for a while.
- |
Toggle Record | Global switch button to activate/deactivate recording. While active, the button blinks red. The button doesn't start recording by itself: if one or more tracks are marked as record-enabled, pressing the - "Play from Playhead" starts recording on those tracks. See - Recording. - + "Play from Playhead" starts recording on those tracks. |
- All these actions are bound to keyboard shortcuts, which allows for speedier - use and more focused work. -
- -- If you synchronize Ardour with other devices then some or all of these control + If Ardour is synchronized with other devices then some or all of these control methods may be unavailable—depending on the synchronization protocol, Ardour may respond only to commands sent from its master device(s).
+- Under these buttons is the Shuttle Speed Control that allows to scrub - through the audio quickly. The slider decides the playback speed : the further - from the center it is set, the faster the playback will scrub in both directions. + Under these buttons is the Shuttle Speed Control that + allows to temporarily scrub through the audio quickly. The slider + decides the playback speed: the further from the center it is set, + the faster the playback will scrub in both directions. The range of + this acceleration can be set by right + clicking the control and setting the multiplier, between 1.5 + (± 150%) and 8 (± 800%).
+ +- The Shuttle Speed Control supports 2 operating modes, that can be chosen with - right click > Mode: + The VS (for VariSpeed) + button sets a constant playback/record speed. It can be set + in semitones (1 semitone = × 2 1⁄12 ≈ + 105,9%), or cents of semitones, and is armed/disarmed by clicking the + button. The VS button will blink when VariSpeed + is enabled. Whether or not this VariSpeed is persistent when + stopping/restarting transport depends on the Reset + default speed on stop parameter in the Preferences.
-On the left of the slider is the positional sync button (which might show Internal, or MTC or several other values), than can be used to control whether or not the @@ -76,6 +87,8 @@ synchronization source, such as MIDI Time Code (MTC), Linear Time Code (LTC) or JACK (see Timecode Generators and Slaves).
+ +The current playback status (Stop, Play, or speed %) is shown on the right of the speed slider. @@ -89,16 +102,17 @@ shows both the default bindings and internal command names for some of them.
-Space | Switch between playback and stop. |
---|---|
Home | Move playhead to session start marker |
End | Move playhead to session end marker |
→ | Playhead to next region boundary |
← | Playhead to previous region boundary |
0 | Move playhead to start of the timeline |
- Go to the