If /set_surface is not sent, the default values are used:
@@ -90,11 +92,27 @@ here"/>
| /set_surface bank_size strip_types - feedback fadermode | + feedback fadermode send_page_size plugin_page_sizeSee below for an explanation of each parameter. |
|---|
+ The /set_surface message may have all values except the last in-line.
+ For example: /set_surface/8/31/8403/0/8 i 16 would be valid.
+ Do be careful of switches which send a 0 on release, it may be necessary
+ to set the value as the release value rather than the press value.
+
+ The /set_surface message may have less than the full set of parameters. + those left out will remain as they were before the /set_surface message was + sent. All parameters included must be valid. For example, setting send page + size would require also setting bank_size, strip_types, feedback and gain mode. + using only two parameters will set bank_size and strip_types. Sending /set_surface with + no parameters will result in Ardour returning a /set_surface message with the + current settings. Surfaces using /set_surface iiii b st fb gm as was the case + in versions of Ardour older than 5.10 will continue to work. +
Bank Size is the number of channel strips the controller supports @@ -168,6 +186,25 @@ here"/>
Gain mode can also be set with /set_surface/gainmode gainmode.
++ Send_page_size is an int for the number of send channels that can be controlled + at one time. Each channel has a name, level and enable control. (added in Ardour 5.10) +
++ Send page size can also be set with /set_surface/send_page_size send_page_size. +
++ plugin_page_size is an int for the number of plugin controls that can be controlled + at one time. Each control has a name and level. As each plugin is different (as is each + parameter), the surface should expect to control the plugin parameters with a variable + control (pot or slider) with a float value from 0 to 1 (even on/off switches). (added in + Ardour 5.10) +
++ Plugin page size can also be set with /set_surface/plugin_page_size plugin_page_size. +
@@ -234,6 +271,20 @@ here"/>
+ New for Ardour 5.9. +
+| /scrub delta | +Where delta is a float indicating forward or reverse movement. + See OSC Scrub Modes |
|---|---|
| /jog delta | +Where delta is a float indicating forward or reverse movement |
| /jog/mode mode | +Where mode is an int from 0 to 7 indicating what the /jog + command controls. See + OSC Jog Modes |
| where gain is a float ranging from -193 to 6 representing the desired gain of the track in dB. | |
| /strip/fader ssid position | where position is a float ranging from 0 to 1 representing the fader control position. |
|---|---|
| /strip/*/automation ssid mode | +where mode is an int ranging from 0 to 3 representing the desired automation mode for the control. + See OSC Automation. |
| /strip/*/touch ssid state | +where state is an int of 1 for touched and 0 for released. + See OSC Automation. |
| /strip/trimdB ssid trim_db | where trim_db is a float ranging from -20 to 20 representing the desired trim of the track in dB. |
| /strip/pan_stereo_position ssid position | @@ -443,6 +500,12 @@ here"/>Where gain is a float ranging from -193 to 6 representing the desired gain of the track in dB. |
| /select/fader position | Where position is an float ranging from 0 to 1 representing the fader control position. |
| /select/*/automation mode | +where mode is an int ranging from 0 to 3 representing the desired automation mode for the control. + See OSC Automation. |
| /select/*/touch state | +where state is an int of 1 for touched and 0 for released. + See OSC Automation. |
| /select/trimdB trim_db | where trim_db is a float ranging from -20 to 20 representing the desired trim of the track in dB. |
| /select/pan_stereo_position position | @@ -463,8 +526,19 @@ here"/> ranging from 0 to 1 representing the desired position for the send as a fader|
| /select/send_enable", sendid state | where sendid = nth_send, state is 1 for enabled and 0 for disabled |
| /select/send_page", delta | +where delta is an int or float selecting another send as a delta from the current send. |
| /select/plugin_page", delta | +where delta is an int or float selecting another plugin parameter as a delta from the current parameter. |
| /select/plugin/parameter", plugin parameter value | +where plugin = nth plugin, parameter = nth parameter and value is a float from 0 to 1 |
+ /select/send_page and /select/plugin_page may be used
+ with a page up and page down switch by using a switch with a value of 1
+ for page up and a switch with a value of -1 for page down. An encoder
+ can be used as well. (these commands were added in Ardour version 5.10)
+
Every single menu item in Ardour's GUI is accessible via OSC. There is