X-Git-Url: http://shamusworld.gotdns.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=include%2Faux-sends.html;h=fcfb1e72e80502324f96da3ba0bc42380f721c78;hb=22361bdd91713484e95096fbb7f5a5297e3919fc;hp=edc5853fa53dac555aff93bb0cd43a469c09a9ec;hpb=2098e011e638b5c86c56e68df7757975fc4d728f;p=ardour-manual diff --git a/include/aux-sends.html b/include/aux-sends.html index edc5853..fcfb1e7 100644 --- a/include/aux-sends.html +++ b/include/aux-sends.html @@ -1,102 +1,105 @@
- Auxilliary sends are Auxilliary sends are simple processors in a bus or track channel strip. They tap the signal at a specific point in the signal flow (pre-fader, post-fader, before or after EQs and other plugins, etc.) - and send a copy of that signal somewhere else, without affecting the + and send a copy of that signal to a bus, without affecting the normal signal flow downwards to the channel fader.
- Usually, aux sends from several tracks are collectively sent to a
- dedicated Aux bus in Ardour, to create a monitor mix for a
- musician, or to feed an effect unit. The output of such a bus might
- be routed to separate hardware outputs (in the case of headphone or monitor
- wedge mixes), or returned to the main mix (in the case of an effect).
- Aux sends are not JACK ports, with
- External Sends Jack ports are created so it is also possible to
+ Aux sends from several tracks are collectively sent to a
+ bus in Ardour, to create a monitor mix for a
+ musician, or to feed an effect unit. A bus used in this way is considered
+ an auxilliary bus or Aux bus even though it is the same as
+ any other bus. The output of such a bus might
+ be routed to separate hardware outputs (in the case of headphone or monitor
+ wedge mixes), or returned to the main mix (in the case of an effect).
+
+ Aux sends are not JACK ports, use + External Sends to send audio to Jack ports. External Sends can send the tapped signal somewhere else directly, which is not usually possible on hardware mixers.
- +- It may be useful to - compare and contrast - the use of aux sends with subgrouping. + It may be useful to + compare and contrast + the use of aux sends with subgrouping.
- Choose Session > Add New Track or Bus. In the - New Track & Bus dialog, select "Busses" in the Track/Bus + Choose Session > Add New Track or Bus. In the + New Track & Bus dialog, select "Busses" in the Track/Bus selector at the upper right.
- Context-click on the processor box for the track you want to send to the bus, and - choose New Aux Send. From the submenu, choose the bus you - want to send to. A send will be added (and will be visible in the processor box). + Context-click on the processor box for the track you want to send to the bus, and + choose New Aux Send. From the submenu, choose the bus you + want to send to. A send will be added (and will be visible in the processor box). Note that the submenu may be empty if you have not created a bus yet.
- Depending on whether you context-click above or below the fader in the processor box, - the new aux send can be placed before or after the fader in the channel strip. - Post-fader aux sends are typically used when using an aux for shared signal + Depending on whether you context-click above or below the fader in the processor box, + the new aux send can be placed before or after the fader in the channel strip. + Post-fader aux sends are typically used when using an aux for shared signal processing (FX), so that the amount of effect is always proportional to - the main mix fader. Pre-fader sends ensure that the level sent to the bus - is controlled only by the send, not the main fader — this is typical - when constructing headphone and monitor wedge mixes. + the main mix fader. Pre-fader sends ensure that the level sent to the bus + is controlled only by the send, not the main fader—this is typical + when constructing headphone and monitor wedge mixes.
- You can add aux sends to all members of a group and connect them to a new aux bus - with a single click. After creating the track group (and adding tracks to it), - context-click on the group tab and choose either - Add New Aux Bus (pre-fader) or - Add New Aux Bus (post-fader). A new aux bus will be created, + You can add aux sends to all members of a group and connect them to a new aux bus + with a single click. After creating the track group + (and adding tracks to it), context-click on the group tab and choose either + Add New Aux Bus (pre-fader) or + Add New Aux Bus (post-fader). A new aux bus will be created, and a new aux send added to every member of the track group that connects to - this aux bus. + this aux bus.
- You can alter the amount of the signal received by a send that it delivers to the bus + You can alter the amount of the signal received by a send that it delivers to the bus it connects to. There are three approaches to this:
- Every send processor has a small horizontal fader that can be adjusted in the usual way. It is - not very big and so this can be a little unsatisfactory if you want very fine control - over the send level. + Every send processor has a small horizontal fader that can be adjusted in the usual way. It is + not very big and so this can be a little unsatisfactory if you want very fine control + over the send level.
- Double-clicking on the send in the processor box will allow you to use the - big fader of the mixer strip to control the send. The visual appearance of - the mixer strip will change to reflect this. Double-click the send again to + Double-clicking on the send in the processor box will allow you to use the + big fader of the mixer strip to control the send. The visual appearance of + the mixer strip will change to reflect this. Double-click the send again to revert back to normal function for the strip.
- Pressing the button marked Aux Sends on a aux bus will - alter the channel strip for every track or bus that feeds the aux bus. Many - aspects of the strip will become insensitive and/or change their visual - appearance. More importantly, the main fader of the affected channel strips - will now control the send level and not the track gain. - This gives a larger, more configurable control to alter the level. Click the - Aux Sends button of the aux bus again to revert the + Pressing the button marked Aux Sends on a aux bus will + alter the channel strip for every track or bus that feeds the aux bus. Many + aspects of the strip will become insensitive and/or change their visual + appearance. More importantly, the main fader of the affected channel strips + will now control the send level and not the track gain. + This gives a larger, more configurable control to alter the level. Click the + Aux Sends button of the aux bus again to revert the channel strips to their normal use.
- Clicking on the small "LED" in the send display in the processor box of the - channel strip will enable/disable the send. When disabled, only silence will - be delivered to the aux bus by this track. When enabled, the signal arriving + Clicking on the small "LED" in the send display in the processor box of the + channel strip will enable/disable the send. When disabled, only silence will + be delivered to the aux bus by this track. When enabled, the signal arriving at the send will be delivered to the aux bus.