- <dfn>Linear Timecode (LTC) Generator</dfn>
- <ul>
- <li>
- <dfn>Enable LTC generator</dfn> when enabled Ardour will
- output an LTC timecode signal on its <em>LTC-out</em> port.
- If this option is checked, the two options below are active:
- </li>
- <li>
- <dfn>Send LTC while stopped</dfn>, when enabled Ardour will
- continue to send LTC information even while the transport (playhead) is
- not moving.
- </li>
- <li>
- <dfn>LTC generator level [dBFS]:</dfn> specifies the peak volume of
- the generated LTC signal in dbFS. A good value is 0dBu=−18dbFS
- in an EBU calibrated system.
- </li>
- </ul>
- </li>
-</ul>
-
-<h3 id="sync_midi">MIDI</h3>
-
-<ul>
- <li>
- <dfn>MIDI Beat Clock (Mclk) Generator</dfn>
- <ul>
- <li>
- <dfn>Enable Mclk generator</dfn> when enabled Ardour will generate a
- (tempo dependant) beat clock at a rate of 24 pulses per quarter note on
- the <code>ardour:MIDI clock out</code> JACK port.
- </li>
- </ul>
- </li>
-
- <li>
- <dfn>MIDI Time Code (MTC) Generator</dfn>
- <ul>
- <li>
- <dfn>Enable MTC Generator</dfn> when enabled Ardour will generate MIDI
- time code on the <code>ardour:MTC out</code> JACK port.
- </li>
- <li>
- <dfn>Percentage either side of normal transport speed to transmit MTC:</dfn>
- MIDI time code generation will be disabled when the transport speed is
- greater than normal speed plus this percentage or less than normal minus
- this percentage.
- </li>
- </ul>
- </li>
-
- <li>
- <dfn>MIDI Machine Control (MMC)</dfn>
- <ul>
- <li>
- <dfn>Respond to MMC commands</dfn> when enabled Ardour will respond
- to MIDI Machine Control commands received on the <code>ardour:MMC in</code>
- JACK port.
- </li>
- <li>
- <dfn>Send MMC commands</dfn> when enabled Ardour will send MIDI Machine
- Control commands on the <code>ardour:MMC out</code>
- JACK port.
- </li>
- <li>
- <dfn>Inbound MMC device ID:</dfn> is the only device ID Ardour will
- respond to when an MMC command is received on the <code>ardour:MMC in</code>
- JACK port.
- </li>
- <li>
- <dfn>Outbound MMC device ID:</dfn> is the MIDI device ID Ardour will
- use when it sends MMC commands.
- </li>
- </ul>
- </li>
-</ul>
-
-<h2 id="control_surfaces">Control Surfaces</h2>
-
-<p>
- This tab contains settings for <a href="@@control-surfaces">control surfaces</a>.
-</p>
-<p>
- It lists all the Control Surface protocols Ardour knows. To enable a
- <dfn>Control Surface Protocol</dfn>, the <kbd class="option">Enable</kbd> checkbox
- next to its name should be ticked. Editing the settings related to this protocol
- can be done by double-clicking its name or clicking the <kbd class="menu">Show
- protocol settings</kbd> (only for Generic MIDI and Open Sound Control).
-</p>
-
-<h2 id="midi_ports">MIDI Ports</h2>
+ <dfn>Plugins</dfn>
+ <ul>
+ <li>
+ <dfn>Silence plugins when the transport is stopped</dfn> when stopping
+ playback or recording, if this option is checked, the plugins that still
+ emit sound (reverbs, etc…) will be stopped. If unchecked, the plugins
+ will continue playing after the transport stop.
+ </li>
+ </ul>
+ </li>
+</ul>
+
+<h3 id="preferences-transport-chase">Chase</h3>