</p>
<h3>strip_types</h3>
<p>
- Strip Types are coming soon... check for more info sometime. For now
- just use 0 (or anything else) as this is ignored. I don't know the bit
- order just yet, but it will work similar to feedback below. Strip Types
- will determine What kind of strips will be included in a bank. This would
- include: Audio, MIDI, busses, VCAs, Master, Monitor and hopefully
- hidden or selected strips.
+ strip_types is an integer made up of bits. The easy way to
+ deal with this is to think of strip_types items being worth a number and
+ then adding all those numbers together for a value to send.
+ Strip Types will determine What kind of strips will be included in
+ bank. This would include: Audio, MIDI, busses, VCAs, Master, Monitor
+ and hidden or selected strips.
</p>
+<p>Please see: <a
+ href="/using-control-surfaces/controlling-ardour-with-osc/calculating-feedback-and-strip-types-values/">
+ Calculating Feedback and Strip-types Values.</a></p>
<h3>feedback</h3>
<p>Feedback is an integer made up of bits. The easy way to
deal with this is to think of feedback items being worth a number and
then adding all those numbers together for a value to send.
</p>
- <ul>
- <li>
- 1 - feedback values of controls in strips.
- </li>
- <li>
- 2 - Send meter values (not coded yet).
- </li>
- <li>
- 4 - Send timecode (not coded yet).
- </li>
- <li>
- 8 - Send Bar and Beat (not coded yet).
- </li>
- <li>
- 16 - Enable master section feedback.
- </li>
- </ul>
-<p>
- So using a value of 17 would turn on feedback for strip and master
- controls, but leave meters, timecode and bar/beat feedback off.
-</p>
+<p>Please see: <a
+ href="/using-control-surfaces/controlling-ardour-with-osc/calculating-feedback-and-strip-types-values/">
+ Calculating Feedback and Strip-types Values.</a></p>
+
<h3>gainmode</h3>
<p>
Gainmode is a an int that acts as a bool:
<h4>Transport Control</h4>
<dl class="bindings">
- <dt><kbd class="osc">/transport_stop</kbd></dt>
+ <dt><kbd class="osc">/transport_stop <em>optional</em></kbd></dt>
<dd></dd>
- <dt><kbd class="osc">/transport_play</kbd></dt>
+ <dt><kbd class="osc">/transport_play <em>optional</em></kbd></dt>
<dd></dd>
<dt><kbd class="osc">/set_transport_speed <em>s</em></kbd></dt>
<dd>where <em>s</em> is a float ranging from -8.0f to 8.0f</dd>
- <dt><kbd class="osc">/ffwd</kbd></dt>
+ <dt><kbd class="osc">/ffwd <em>optional</em></kbd></dt>
<dd></dd>
- <dt><kbd class="osc">/rewind</kbd></dt>
+ <dt><kbd class="osc">/rewind <em>optional</em></kbd></dt>
<dd></dd>
<dt><kbd class="osc">/goto_start</kbd></dt>
<dd></dd>
<dd>where <em>spos</em> is the target position in samples and
<em>roll</em> is a bool/integer defining whether you want transport
to be kept rolling or not</dd>
- <dt><kbd class="osc">/loop_toggle</kbd></dt>
+ <dt><kbd class="osc">/loop_toggle <em>optional</em></kbd></dt>
<dd></dd>
</dl>
<dd></dd>
<dt><kbd class="osc">/toggle_punch_out</kbd></dt>
<dd></dd>
- <dt><kbd class="osc">/rec_enable_toggle</kbd></dt>
+ <dt><kbd class="osc">/rec_enable_toggle <em>optional</em></kbd></dt>
<dd></dd>
<dt><kbd class="osc">/toggle_all_rec_enables</kbd></dt>
<dd>(toggles all tracks' recording state)</dd>
Monitor, may be included in the list of SSIDs or not as set in
<em>/set_surface</em>.
</p>
+<p class="note">
+ Some Surfaces (many Android applets) are not able to deal with more
+ than one parameter in a command. However, the two parameter commands
+ below can also be sent as /strip/command/ssid param. In this case the
+ param should be a float even if an int is required below.
+</p>
<dl class="bindings">
- <dt><kbd class="osc">/bank_up</kbd></dt>
+ <dt><kbd class="osc">/bank_up </kbd></dt>
<dd>Change bank to the next higher bank.</dd>
- <dt><kbd class="osc">/bank_down</kbd></dt>
+ <dt><kbd class="osc">/bank_down </kbd></dt>
<dd>Change bank to the next lower bank.</dd>
<dt><kbd class="osc">/strip/mute <em>ssid</em> <em>mute_st</em></kbd></dt>
<dd>where <em>mute_st</em> is a bool/int representing the desired mute state of the track</dd>
<dt><kbd class="osc">/strip/solo <em>ssid</em> <em>solo_st</em></kbd></dt>
<dd>where <em>solo_st</em> is a bool/int representing the desired solo state of the track</dd>
+ <dt><kbd class="osc">/strip/monitor_input <em>ssid</em> <em>monitor_st</em></kbd></dt>
+ <dd>where <em>monitor_st</em> is a bool/int where 1 is forced input monitoring.</dd>
+ <dt><kbd class="osc">/strip/monitor_disk <em>ssid</em> <em>monitor_st</em></kbd></dt>
+ <dd>where <em>monitor_st</em> is a bool/int where 1 is forced disk monitoring. When input and disk are both off,
+ Auto monitoring is enabled.</dd>
<dt><kbd class="osc">/strip/recenable <em>ssid</em> <em>rec_st</em></kbd></dt>
<dd>where <em>rec_st</em> is a bool/int representing the desired rec state of the track</dd>
<dt><kbd class="osc">/strip/gain <em>ssid</em> <em>gain</em></kbd></dt>